Tesla变压器型电子束加速器初步实验

 介绍了一种Tesla变压器型的强流电子束加速器。当变压器初级输入20kV左右的电压时，加速器二极管输出电压500kV，电流9kA，信号脉宽大约50ns，该装置具有结构简单，安装方便，运行可靠等特点。     

用气相色谱仪测定变压器油中气体

本文采用多柱自动切换气相色谱仪和真空全脱气装置对变压器和互感器用油中的气体进行了系统的分析，除可测定油中的氢、甲烷、乙炔、乙烯、乙烷、二氧化碳和一氧化碳等气体外，还可根据不同需要测定氮、氧以及Ｃ３和Ｃ４烃的含量。本方法已用于诊断变压器和互感器内部变化及故障。     

Graded PZT ceramics for piezoelectric transformers

In the present study two types of the synthesized Pb(Zr_1−xTi_x)O₃ (PZT) powders differing in Zr/Ti ratio were used to prepare the spatially inhomogeneous (i.e., graded) structure. A position-dependent chemical composition was expected to cause the property gradient. Disk-shaped compacts were prepared in a way such that two different orientations of the radial gradients were formed. The solid state sintering under pressure was utilized to prepare ceramics. Simultaneous thermal analysis was used to study thermal behavior of the ceramic powders. Graded PZT ceramics were characterized using X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy. It was also characterized in terms of its dielectric properties by both bridge technique and the impedance spectroscopy. On the basis of graded PZT ceramics the disk-shaped radial mode piezoelectric transformer was developed and fabricated.     

Investigation and optimization of the recovery of coal fines using oil agglomeration process: Use of waste oils from different sectors

The high cost of the bridging liquid subdues the implementation and commercialization of oil agglomeration process. To overcome this problem, waste oils from different sectors were used in this present study. The performance of the process was assessed based on the responses like ash rejection and organic matter recovery. The aim of the present study was to investigate the usage of waste oils from different sectors and to optimize and analyze the behavioral pattern showcased by different variables (pulp density, oil dosage, agglomeration time and oil type) using response surface methodology (Box-Behnken design). Experimental investigation shows that the optimum pulp density, oil dosage, agglomeration time and oil type condition obtained as 3%, 15%, 15?min and waste engine oil, respectively. At optimum condition, the % ash rejection and % organic matter recovery obtained as 63.94% and 81.8%, respectively.     

300kVA高温超导变压器电流引线漏热损耗的测量

电流引线是高温超导变压器的主要外部漏热来源,它的漏热量直接影响了超导变压器的经济性能,因此,引线的设计与漏热测量一直备受关注。文中构建了一个实验方案,运用量热法测量低压引线的漏热,并将试验结果与仿真预期值进行了对比和分析,从而验证了仿真设计的正确性。     

利用弧形光栅尺测量大型转轴扭矩的原理研究

利用弧形光栅尺的旋转微位移测量功能,组建一组测量体系,用于测量巨型转轴的扭矩。采用四组相同的弧形光栅尺同时测量两截面的相对转角,通过多点测量实现误差均化,得出了消除转轴直径对测量影响的公式,使仪器的环境适应能力得到了极大地提高。根据不同的工作情况,提出了相应的动态测量扭矩的计算方程。实现了大型机械设备主传动的动力监测,为设备自动化、智能化奠定了基础。     

新颖的CMOS四值译码器与编码器

利用多级离子注入技术,一种新型的 C M O S 四值译码器与编码器被设计.它们有一 个低功耗与低输出阻抗的简单结构,可以用作超大规模集成电路设计中的接口电路,以减 少基片的外部引线数     

高精度绝对式光电轴角编码器

本文介绍高精度绝对式19-bit、21-bit光电轴角编码器的工作原理、具体结构、精度和可靠性等.采用移相电阻链细分和分段多次校正的方法对提高绝对式编码器的分辨率、精度和可靠性是有效的手段之一.检测结果:19-bit编码器的分辨率准确度σ=±0.6″ ,测角准确变σ=±1.2″;21-bit编码器的分辨率准确度σ=±0.2″,测角准确度,σ=±0.62″.其中,19-bit绝对式编码器早已用于光测设备中.     

PPCP用固态脉冲电源的实验研究

 介绍了一种采用半导体开关与磁开关、可饱和脉冲变压器相结合技术的固态脉冲电源，此电源可用于脉冲放电等离子体烟气治理。在理论分析的基础上建立了实验模型，通过实验验证了此类电源的可行性，解决了8支晶闸管开关串联的动静态均压及开通同步性问题，并对可饱和脉冲变压器及磁开关的工作特性进行了分析计算。电源在阻性负载上得到峰值电压37.5 kV、前沿101 ns、脉宽1 μs的脉冲，重复频率300 Hz，输出功率10 kW。     

快脉冲直线变压器驱动源模块的原理及实验

 介绍了直线型变压器驱动源（LTD）产生快脉冲的基本原理及技术优势，阐述了快脉冲LTD模块设计的要点，设计了输出脉冲上升时间小于100 ns的快脉冲LTD模块，并进行了初步的实验研究。实验得到该LTD模块充电±16 kV时，短路放电的电流峰值为23.7 kA，电流振荡1/4周期为69.6 ns；充电±50 kV驱动0.85 Ω负载时，电流峰值为41.4 kA，上升时间为36.8 ns（10%~90%）和60.8 ns（0~100%）。